Allen-Bradley 150-F60NBR SMC Flex Smart Motor Controller

Deliver smooth, protected starts for mid-range motors. The Allen-Bradley 150-F60NBR is a versatile 60-amp smart motor controller. It provides soft-start and soft-stop control for motors up to 40 HP, reducing wear and tear. With its intuitive LCD interface and robust protection suite, the 150-F60NBR is a reliable solution for pumps, fans, and conveyors.

What Makes This Controller Stand Out:

• Optimized for 40 HP Motors: Provides the right amount of control for common industrial motor sizes.
• Comprehensive Motor Protection: Built-in safeguards against overloads, voltage issues, stalls, and phase loss.
• Easy to Configure: Backlit LCD and keypad allow for quick setup and troubleshooting on the spot.
• Seven Operating Modes: Flexibility with Soft Start, Current Limit, Dual Ramp, Full Voltage, and more.
• Rugged Industrial Design: Built to withstand vibration and shock in demanding plant environments.

Complete Technical Specifications

Manufacturer: Allen-Bradley (Rockwell Automation)

Series: SMC-Flex Smart Motor Controller

Model: 150-F60NBR

Rated Current: 60 Amperes

Horsepower Rating: 40 HP @ 460V AC

Input Voltage: 200-460V AC, 3-Phase, 50/60 Hz

Control Voltage: 24V AC or DC

Enclosure: Open Type (Panel Mount Required)

Standard Operating Modes: Soft Start, Current Limit, Dual Ramp, Full Voltage, Linear Speed, Preset Slow Speed, Soft Stop

Key Protection Features: Electronic Overload, Stall/Jam, Phase Reversal, Voltage Unbalance, Under/Over Voltage

User Interface: Backlit LCD with Keypad, LED Status Indicators

Operating Temperature: -5°C to 40°C (23°F to 104°F)

Storage Temperature: -20°C to 75°C (-4°F to 167°F)

Vibration Resistance: 1 g (Operating), 2.5 g (Non-Operating)

Pollution Degree: 2 (for non-conductive contamination only)

Weight: 12.50 kg (27.56 lbs)

Dimensions (approx.): 320mm x 150mm x 203mm (12.6" x 5.9" x 8")

Installation & Setup Guide

Mount the 150-F60NBR securely inside a protective industrial control panel. Ensure adequate space for airflow around the unit. Connect the 3-phase line input and motor load wires. Supply 24V AC or DC control power. Use the front keypad to enter the motor's nameplate Full Load Amps (FLA) and select the desired start/stop mode. Always install a properly rated circuit breaker or fused disconnect on the line side.

Warranty Coverage

This Allen-Bradley product is covered by a standard 12-month warranty, guaranteeing it is free from material and workmanship defects.

Practical FAQs

What is "Pollution Degree 2" and why does it matter?

It means the controller is designed for environments where only non-conductive dust is present. Condensation, conductive dust, or corrosive fumes require a higher protection enclosure.

Can I use this to replace a traditional motor starter?

Yes, absolutely. It can directly replace a contactor and overload relay setup, adding soft-start benefits while providing superior protection.

How do I choose between "Soft Start" and "Current Limit" mode?

Use "Soft Start" for a smooth, linear ramp of voltage. Choose "Current Limit" to cap the inrush current at a set level (e.g., 300% FLA), useful for weak power supplies.

The controller faulted on "Voltage Unbalance." What should I check?

First, verify all three-phase input connections are tight. Then, use a multimeter to check the incoming line-to-line voltages. A difference greater than 2% can trigger this protection.

Is the "Linear Speed" mode easy to set up?

This mode requires an optional tachometer feedback card. It's more complex but provides the most precise speed control for applications like winding machines.

Shipping Information
This item is in stock and ready for immediate shipment via FedEx, UPS, or DHL. Tracking is provided with every order.

© 2025 Ubest Automation Limited. All rights reserved.
Original Source: https://www.ubestplc.com/
Contact: sales@ubestplc.com Phone: +86 180 3000 5825