Allen-Bradley 1440-VSE02-01RA XM Vibration Module – 2 Channel DeviceNet Monitor

The 1440-VSE02-01RA is a vibration monitoring module from the Allen-Bradley XM series. It reads two sensor channels and sends data over DeviceNet at a fixed 19,200 bps rate. Maintenance teams use this module to watch low-frequency machine vibration in real time. The 1440-VSE02-01RA mounts on a terminal base and reports status through seven LED indicators.

Summary

• The 1440-VSE02-01RA comes from the Allen-Bradley XM vibration product line.
• Two input channels accept vibration sensor signals for continuous machine monitoring.
• DeviceNet communication links the module to existing control networks.
• Seven red and green LEDs show channel and network status at a glance.
• Two isolated outputs keep signal paths clean in noisy plant environments.

Core Specifications

• Manufacturer: Allen-Bradley (Rockwell Automation)
• Model: 1440-VSE02-01RA
• Product line: XM
• Product type: Vibration module
• Input channels: 2
• Communication: DeviceNet protocol
• Baud rate: 19,200 bps, fixed
• Supply voltage: 24 V DC
• Sampling mode: Synchronous or asynchronous
• Frequency range: 1 Hz to 20 Hz
• Input impedance: greater than 100 kOhm
• Isolated outputs: 2
• Status display: seven red and green LEDs
• Mounting: terminal base
• UPC: 781180000171
• GTIN: 10781180000178
• Weight: 0.34 kg (0.75 lbs)

Power and Thermal Data

• Typical current draw reaches 175 mA, and peak draw reaches 300 mA.
• Normal heat output sits near 4 W, with a 7 W ceiling under full load.
• Low heat generation helps keep cabinet temperatures stable.
• Efficient power use supports dense panel layouts without extra cooling.

Key Selling Points

• Dual channels let one module monitor two measurement points at once.
• DeviceNet support cuts wiring cost by sharing one network cable.
• The fixed baud rate keeps data traffic predictable and easy to validate.
• Isolated outputs block ground loops that often distort vibration signals.
• High input impedance above 100 kOhm accepts many sensor types.
• The terminal base design speeds swap-out during planned maintenance.
• Seven LEDs shorten fault finding to a single glance at the front panel.
• Synchronous sampling captures phase data for balance and alignment work.
• Asynchronous sampling suits simple trend monitoring on slow machines.

Installation Guide

• Snap the module onto a compatible XM terminal base before wiring.
• Feed 24 V DC supply power and confirm polarity at the terminals.
• Connect sensor cables to both input channels and check shield grounding.
• Set the DeviceNet node address to a free value on the network.
• Keep the fixed 19,200 bps rate in mind when planning bus length.
• Route sensor leads away from drive cables to reduce noise pickup.
• Verify LED patterns after power-up and confirm normal status.

Package Contents

• 1 × 1440-VSE02-01RA vibration module
• 1 × installation reference sheet
• 1 × terminal base connection guide

Warranty and Shipping

• Every unit carries a 12-month warranty against manufacturing defects.
• FedEx, UPS, and DHL deliver orders to most global destinations.
• Tracking details arrive by email after the carrier collects the parcel.
• Stock availability and lead times appear on the product page.

FAQ

• Q: What sensor types pair with the 1440-VSE02-01RA?
  A: It accepts standard vibration sensors whose output fits the input range and impedance.
• Q: Why does the module use a fixed baud rate?
  A: A fixed 19,200 bps rate keeps DeviceNet traffic stable and simple to troubleshoot.
• Q: Can I run both channels in different sampling modes?
  A: Yes. The module supports synchronous and asynchronous sampling across its two channels.
• Q: How do I read module status without software?
  A: The seven red and green LEDs show channel health and network state directly.
• Q: What supply current should I plan for?
  A: Allow 300 mA at peak load and 175 mA for typical operation.

© 2026 Ubest Automation Limited. https://www.ubestplc.com/ All rights reserved.

Contact: sales@ubestplc.com | +86 86 180 3000 5825