Bently Nevada 3300 XL 11mm Proximity Probe with 5-Meter Armored Cable

This Bently Nevada 330707-00-24-50-12-00 is a heavy-duty industrial sensor. It has a long 5-meter armored cable for extended reach. The cable also features FluidLoc technology to resist moisture. The probe body uses strong 304 stainless steel. Its tip is made from tough PPS plastic. This sensor is perfect for large or hard-to-reach machines. It must pair with a 5-meter Proximitor sensor. Get reliable vibration data in tough conditions.

Part Number Configuration: 330707-00-24-50-12-00

• 330707 (Base Model):
  • 3300 XL Monitoring System Family.
  • 11mm Diameter Proximity Probe.
  • 1/2-20 UNF Thread with Stainless Steel Armor.
• 00 (Unthreaded Length): 0.0 inches. The case is fully threaded.
• 24 (Case Length): 2.4 inches total length.
• 50 (Cable Length): 5.0 meters (16.4 feet) long.
• 12 (Connector & Cable): ClickLoc connector with FluidLoc cable.
• 00 (Approvals): No special agency certifications required.

Detailed Technical Specifications

• Brand & Full Model: Bently Nevada 330707-00-24-50-12-00
• Product Series: 3300 XL Vibration Monitoring
• Sensing Principle: Eddy-Current Displacement
• Probe Diameter: 11 mm
• Tip Material: Durable Polyphenylene Sulfide (PPS)
• Case Material: AISI 304 Stainless Steel
• Cable Type: 75 Ohm Triaxial
• Cable Protection: Stainless Steel Armor & FluidLoc Moisture Barrier
• Cable Insulation: FEP (High-Temperature Resistant)
• Total Cable Length: 5.0 Meters (16.4 Feet)
• Electrical Resistance (5m): 7.2 Ohms ± 0.8 Ohms
• Output Signal: Gap Voltage (Requires compatible monitor)
• Mounting Thread: 1/2-20 UNF
• Alternative Thread: M16 x 1.5 mm
• Max Thread Engagement: 0.750 inch (1/2-20)
• Installation Torque: 15.2 N·m (133 in-lb)
• Max Torque: 45.2 N·m (400 in-lb)
• Connector Type: ClickLoc Coaxial
• Connector Torque: Hand Tight Only
• Cable Bend Radius: Min 25.4 mm (1.0 inch)
• Operating Temperature: -51°C to +177°C (-60°F to +351°F)
• Seal: Pre-installed Viton O-Ring
• Low-Temp Warning: Do not install below -34°C (-29°F)

Installation Guide

• This 330707-00-24-50-12-00 probe works only with 5-meter Proximitor sensors.
• Plan a safe route for the 5-meter armored cable.
• Clean the mounting hole threads before installation.
• Hand-start the probe to avoid cross-threading.
• Use a torque wrench to tighten to 15.2 N·m.
• Push the ClickLoc connector until it clicks into place.
• Do not bend the cable tighter than 1-inch radius.
• Keep the probe above -34°C before installing.

Compatibility Information

This probe is designed for Bently Nevada 3300 XL monitoring systems. You must use it with a matching 5-meter cable Proximitor sensor. The armored FluidLoc cable is ideal for wet or physically demanding environments.

Certifications & Approvals

This product (suffix -00) is for general industrial use. It does not carry specific hazardous area certifications like ATEX or CSA.

Package Contents & Warranty

• One Bently Nevada 3300 XL 11mm Proximity Probe.
• One integrated 5-meter armored FluidLoc cable with ClickLoc connector.
• All necessary sealing components (O-ring).
• This product includes a 12-month warranty against defects.

Shipping Information

We ship worldwide using FedEx, UPS, and DHL. You will receive tracking information after your order ships.

Frequently Asked Questions (FAQ)

What are the main benefits of the armored FluidLoc cable?

The armor gives crush and abrasion protection. The FluidLoc layer stops liquids from wicking inside the cable. This combination is for harsh, wet areas.

Can I use a different cable length Proximitor with this probe?

No. System calibration requires matching lengths. This 5-meter 330707-00-24-50-12-00 probe only works with a 5-meter Proximitor.

What is the typical measurement range for this probe?

The measurable gap range depends on the connected monitor. Common systems offer a range up to 80 mils (2 mm) or more.

Is the probe safe to use in outdoor conditions?

The armored FluidLoc cable provides good protection. However, it is not designed for continuous submersion. Protect connections from direct weather exposure.

How do I know if my application needs this probe?

Choose this model if you need a long cable run (5m) in an area with physical risks or moisture. Also ensure your monitoring system uses 5-meter Proximitors.

© 2025 Ubest Automation Limited. All rights reserved.
Original Source: https://www.ubestplc.com/
Contact: sales@ubestplc.com | Phone: +86 180 3000 5825